Content on this page requires a newer version of Adobe Flash Player.

Get Adobe Flash player

 
 

ELECTROMAGNETIC CHUCK

Series UL - 714
ELECTROMAGNETIC CHUCK

• HEAVY DUTY ELECTROMAGNETIC RECTANGULAR CHUCK
• Work holding device for surface grinding machines.
• Each pole is having separate coil, as such very strong & even magnetic flux is generated. 
• Accuracy as per IS : 8710 - 1978.
• Magnetic pull is 30-50% more then IS specification.
• Mag - D - Mag with variable control unit allows to neutralize the residual magnetism precisely, using a microprocessor based control circuitry.
• Variable supply to vary power which helps in alignment
& removing of warpages of thin jobs.
• Chuck is tested for Slippering force, Waterproof test, Temperature rise test, Electrical & Demagnetizing tests.
• Also available in Longitudinal Poles.
• We also manufacture Special chucks to suit individual requirements.
• Good quality & standard electrical accessories.

 
Sr. No. 
Cat No.
Size (mm)
Pole Gap (mm)
Pole Pitch
1.
UL-71401
450 L x 150 W x 100 H
15
40
2.
UL-71402
500 L x 200 W x 100 H
15
40
3.
UL-71403
600 L x 200 W x 100 H
15
40
4.
UL-71404
600 L x 250 W x 100 H
15
40
5.
UL-71405
750 L x 250 W x 100 H
15
40
6.
UL-71406
900 L x 250 W x 100 H
15
40
7.
UL-71407
600 L x 300 W x 100 H
15
40
8.
UL-71408
750 L x 300 W x 100 H
15
40
9.
UL-71409
900 L x 300 W x 100 H
15
40
10.
UL-71410
1000 L x 250 W x 110 H
15
40
11.
UL-71411
1000 L x 300 W x 110 H
15
40
12.
UL-71412
1500 L x 250 W x 110 H
15
40
13.
UL-71413
1500 L x 300 W x 110 H
15
40
14.
UL-71414
1500 L x 400 W x 110 H
15
40
15A.
"ULTRA" MAG d- MAG WITH VARIABLE
Upto 1000L 2 Amp.
CONTROL UNIT
Upto 1500L 3 Amp.
15B.
"ULTRA" MAG d- MAG WITH VARIABLE
Upto 1000L 2 Amp.
CONTROL UNIT & BATTERY BACK UP (20MIN) 
Upto 1500L 3 Amp.
 
 
 

MULTI COIL ELECTRO MAGNETIC CHUCK FINE PITCH

Series UL - 715
MULTI COIL ELECTRO MAGNETIC CHUCK FINE PITCH

• HEAVY DUTY FINE PITCH MULTI COIL ELECTRO MAGNETIC CHUCK (transverse Pole)
   IS - 8710 - 1978

• Work holding device for surface grinding machines. 
• Each pole is having separate coil, as such very strong & even magnetic flux is generated. 
• Accuracy as per IS : 8710 - 1978. 
Magnetic pull is 30-50% more then IS specification. 
Fine Pitch (4 + 1) makes it suitable to hold thin & small jobs. 
• Mag - D - Mag with variable control unit allows to neutralize the residual magnetism precisely, using a microprocessor based control circuitry. 
• Variable supply to vary power which helps in alignment & removing of warpages of thin jobs. 
• Chuck is tested for Slippering force, Waterproof test, Temperature rise test, Electrical & Demagnetizing tests. 
• Also available in Longitudinal Poles. 

 
Sr. No. 
Cat No.
Size (mm)
Pole Gap (mm)
1.
UL-71501
450 L x 150 W x 100 H
4 + 1
2.
UL-71502
500 L x 200 W x 100 H
4 + 1
3.
UL-71503
600 L x 200 W x 100 H
4 + 1
4.
UL-71504
600 L x 250 W x 100 H
4 + 1
5.
UL-71505
750 L x 250 W x 100 H
4 + 1
6.
UL-71506
900 L x 250 W x 100 H
4 + 1
7.
UL-71507
600 L x 300 W x 100 H
4 + 1
8.
UL-71508
750 L x 300 W x 100 H
4 + 1
9.
UL-71509
900 L x 300 W x 100 H
4 + 1
10.
UL-71510
1000 L x 250 W x 110 H
4 + 1
11.
UL-71511
1000 L x 300 W x 110 H
4 + 1
12.
UL-71512
1500 L x 250 W x 110 H
4 + 1
13.
UL-71513
1500 L x 300 W x 110 H
4 + 1
14.
UL-71514
1500 L x 400 W x 110 H
4 + 1
15A.

"ULTRA" MAG D- MAG WITH VARIABLE CONTROL UNIT

Upto 1000L 2 Amp.
Upto 1500L 3 Amp.
15B.

"ULTRA" MAG D- MAG WITH VARIABLE CONTROL UNIT & BATTERY BACK UP (20MIN) 

Upto 1000L 2 Amp.
Upto 1500L 3 Amp.
 
 
 

MULTI COIL MICRO FINE PITCH ELECTRO MAGNETIC CHUCKS

Series UL - 722
MULTI COIL MICRO FINE PITCH ELECTRO MAGNETIC CHUCKS

• MULTI COIL MICRO FINE PITCH ELECTRO MAGNETIC CHUCK
• Work holding device for surface grinding machines.
• Each pole is having separate coil, as such very strong & even magnetic flux is generated.
• Accuracy as per IS : 8710 - 1978.
• Magnetic pull is 30-50% more then IS specification.
• Fine Pitch (1 + 0.5) makes it suitable to hold very thin & small jobs.
• Mag - D - Mag with variable control unit allows to neutralize the residual magnetism precisely , using a microprocessor based control circuitry.
• Variable supply to vary power which helps in alignment & removing of warpages of thin jobs.
• Chuck is tested for Slippering force, Waterproof test, Temperature rise test, Electrical & Demagnetizing tests.
• Good quality & standard electrical accessories.
We also manufacture Special chucks to suit individual requirement.

 
Sr. No. 
Cat No.
Size (mm)
Pole Gap (mm)
1.
UL-72201
450 L x 150 W x 100 H
1.5
2.
UL-72202
450 L x 200 W x 100 H
1.5
3.
UL-72203
500 L x 200 W x 100 H
1.5
4.
UL-72204
600 L x 250 W x 100 H
1.5
5.
UL-72205
750 L x 250 W x 100 H
1.5
15A.

"ULTRA" MAG D- MAG WITH VARIABLE CONTROL UNIT

 2 Amp.
15B.

"ULTRA" MAG D- MAG WITH VARIABLE CONTROL UNIT & BATTERY BACK UP (20 minutes) 

2 Amp.
 
 
 
ELECTRO MAGNET CHUCK CONTROLLER
 

ELECTRO MAGNET CHUCK CONTROLLER

 

These Electro Magnet Controller are designed for high durability and smooth operation on all surfaces. It is used to detect and check the vehicles before their entry to the important places. It is easy to use while presenting the least amount of fatigue to the user. These are designed precisely in different compact designs and specifications lay down by our clients.

Feature :
Controller is having facility of Magnet on, Magnet off, D Magnet and variable clob

Controller are available from 1 Amp upto 20 Amp

 

 
 
 
ELECTRO MAGNETIC ROUND CHUCK
Series UL - 716
ELECTRO MAGNETIC ROUND CHUCK

ELECTRO MAGNETIC ROUND CHUCK IS : 8710 - 197
• Work holding device for Rotary surface grinding machine & lathe machines.
• Each pole is having separate coil, as such very strong & even magnetic flux is generated.
Magnetic pull is 30-50% more then IS specification.
• Mag - D - Mag with variable control unit allows to neutralize the residual magnetism precisely , using a microprocessor based control circuitry. 
• Variable supply for varying power which helps in alignment & removing of warpages of thin jobs. 
• The chuck is also useful for second operation 
• Chuck is tested for Slippering force, Waterproof test
• Temperature rise test, Electrical & Demagnetizing tests.

 
Sr. No. 
Cat No.
Size (mm)
Circular Pole Gap (mm)
1.
UL-71601
Ø300 X 100H
10 + 5
2.
UL-71602
Ø450 X 100H
10 + 5
3.
UL-71603
Ø600 X 100H
10 + 5
4.
UL-71604
Ø750 X 100H
10 + 5
5.
UL-71605
Ø1000 X 100H
10 + 5
5A.

"ULTRA" MAG D- MAG WITH VARIABLE CONTROL UNIT

 2 Amp.
5B.

"ULTRA" MAG D- MAG WITH VARIABLE CONTROL UNIT

2 Amp. & above
 
 
 
 
ELECTRO MAGNETIC CHUCK For Cylindrical Grinding
Series UL - 720
ELECTRO MAGNETIC CHUCK For Cylindrical Grinding

• Work holding device on Cylindrical Grinding m/c to grind outer diameter & face component as bearing recess, flanges, collet bushes, discs etc. 
• Can also be used on Lathe machine. 
• Mag - D - Mag with variable control unit allows to neutralize the residual magnetism precisely  Magnetic Coil (outer body) remains stationary & middle part (Round body) will rotate with spindle through adaptor sleeve.
• Variable supply is useful to true the job.
• 4 T-slots for easy location of job.
• Chuck is tested for Slippering force, Temperature rise, Waterproof,
• Electrical & Demagnetizing tests Good quality & standard electrical accessories. 
• Battery Back-up unit is also available on request

 
Sr. No. 
Cat No.
Size (mm)
1.
UL 72001
Ø100 [4"]
Ø150 [6"]
Ø200 [8" ]
2.

 "ULTRA" Mag- D-MAG Mag with Variable Control Unit

 
 
 
FINE PITCH ELECTROPERM MAGNETIC CHUCK For Grinding Machine
 
FINE PITCH ELECTROPERM MAGNETIC CHUCK For Grinding Machine

• Work holding device for surface grinding machines.
• COLD DEVICE as it doesn't require power continuously except for short period of activation & deactivation.
• Parallelism & flatness is 0.010mm/300mm.
• Suitable for thin & small jobs.
• Economical for operation & maintenance.
• Uniform clamping force all over surface.
• Negligible power consumption.
• No accidents due to power failure.
• Slippering force is 2.5 Kg/cm².
• Vertical Lifting Force is 35 - 40 Kg/cm².
• Variable supply unit to vary power which helps in alignment & removing of warpages of thin jobs.
• Chuck is tested for Slippering force, Waterproof test, Temperature rise test, Electrical & • Demagnetizing tests.
• Good quality & standard electrical accessories.
• We also manufacture Special chucks to suit individual requirement.

 
Sr. No. 
Cat No.
Size (mm)
Pole Gap (mm)
1.
UL 72301 
450 L x 150 W x 100 H
4 + 1
2.
UL-72302
500 L x 200 W x 100 H
4 + 1
3.
UL-72303
600 L x 200 W x 100 H
4 + 1
4.
UL-72304
600 L x 250 W x 100 H
4 + 1
5.
UL-72305
750 L x 250 W x 100 H
4 + 1
6.
UL 72306 
900 L x 250 W x 100 H
4 + 1
7.
UL 72307
600 L x 300 W x 100 H
4 + 1
8.
UL 72308 
750 L x 300 W x 100 H
4 + 1
9.
UL 72309 
900 L x 300 W x  100 H
4 + 1
10.
UL 72310 
1000 L x 250 W x 110 H
4 + 1
11.
UL 72311
1000 L x 300 W x 110 H
4 + 1
12.
UL 72312 
1500 Lx 250 W x 110 H
4 + 1
13.
UL 72313 
1500 L x 300 W x 110 H
4 + 1
14.
UL 72314
1500 Lx 400 W x 110 H
4 + 1
15.
“ULTRA” CONTROL UNIT WITH VARIABLE SUPPLY 
4 + 1
 
 
 
ELECTROPERM MAGNETIC CHUCK for Horrizontal Machining
Series UL - 816
ELECTROPERM MAGNETIC CHUCK for Horrizontal Machining

• EPM CHUCK is designed in such a way that it is very useful for Horizontal machining centers. It is also useful in conventional machining for Horizontal milling operation.

• As Electro Permanent Magnetic (EPM) Principle is used 
Continues Electrically is not required.


• Easily intergrated with pallet clamping

• Manufactured as per customer requirement

 
 
 
 
ELECTRO PERMANENT MAGNETIC CHUCK
Series UL - 718
ELECTRO PERMANENT MAGNETIC CHUCK

• ELECTROPERM LIGHT DUTY CHUCK (47 x 47 Quard Pole)
• Work holding device for Milling machines.
• COLD DEVICE as it doesn't require power continuously except for short period of    activation & deactivation.
• Suitable for light milling i.e. 1-3 mm depth of cut at recommended speed & feed. 
• Maximum material removal is possible.
• Economical for operation & maintenance.
• No accidents due to power failure.
• Slippering force is 2.5 - 3 Kg/cm².
• Vertical Lifting Force is 35 - 40 Kg/cm².
• Variable supply unit to vary power which helps in alignment of jobs.
• Chuck is tested for Slippering force, Waterproof test, Temperature rise test, Electrical & Demagnetizing tests.
• Good quality & standard electrical accessories.
We also manufacture Special chucks to suit individual requirement.

 
Sr. No. 
Cat No.
Size (mm)
1.
UL 71801
600 L x 300 W x 110 H
2.
UL-71802
750 Lx 300 W x 110 H
3.
UL- 71803
1000 Lx 300 W x110 H
4.
UL- 71804
1500 Lx 300 W x 110 H
5.
UL- 71805
600 Lx 400 W x 110 H
6.
UL- 71806
750 Lx 400 W x 110 H
7.
UL -71807
1000 Lx 400 W x 110 H
8.
UL-71808
1500 Lx 400 W x 110 H
9.

ULTRA CONTROL UNIT WITH VARIABLE SUPPLY

 
 
 
ELECTRO PERMANENT MAGNETIC CHUCKS
Series UL - 719
ELECTRO PERMANENT MAGNETIC CHUCKS

• ELECTROPERM HEAVY DUTY CHUCK (70 x 70) Quard Pole
• Work holding device for conventional & CNC milling m/c.
• COLD DEVICE as it doesn't require power continuously except for short period of activation & deactivation.
• Suitable for light milling i.e. 3-6 mm depth of cut at recommended speed & feed.
• Maximum material removal is possible.
• Economical for operation & maintenance.
• No accidents due to power failure.
• Slippering force is 2.5 - 3.5 Kg/cm².
• Vertical Lifting Force is 40 - 45 Kg/cm².
• Variable supply unit to vary power which helps in alignment of jobs. 
• Chuck is tested for Slippering force, Waterproof test, Temperature rise test,
   Electrical & Demagnetizing tests.
• Good quality & standard electrical accessories.
• We also manufacture Special chucks to suit individual requirement

 
Sr. No. 
Cat No.
Size (mm)
1.
UL 71901
600 L x 300 W x 110 H
2.
UL-71902
750 L x 300 W x 110 H
3.
UL- 71903
1000 L x 300 W x 110 H
4.
UL- 71904
1500 L x 300 W x 110 H
5.
UL- 71905
600 L x 400 W x 110 H
6.
UL- 71906
750 L x 400 W x 110 H
7.
UL -71907
1000 L x 400 W x 110 H
8.
UL-71908
1500 L x 400 W x 110 H
9.

ULTRA CONTROL UNIT WITH VARIABLE SUPPLY

 
 
 
MAGNETIC ROUND CHUCK FOR TURNING
Series UL - 821
MAGNETIC ROUND CHUCK FOR TURNING
MAGNETIC ROUND CHUCK FOR TURNING
 

Application :
• ELECTROPERM MAGNETIC ROUND CHUCK FOR TURNING
• Use in vertical and horizontal turning of Plates.
• Radially movable location blocks will help to position and secure work pieces.
For Heavy Turning
• Double magnet is available for heavy duty operations on seamless rolled rings, turning
flanges and machining plates.

   
ID, OD and face machining in one setup
 
   
Feature :
1. ID, OD & Face Machining In One Setup which no other work-holder will provide.
2. Detachable Bayonet Plug for power supply.
3. Poles Individually Magnetized for full loading power. Also Simple Pole
Extensions allows tool elearance for rings.
4. Assembled with power full magnets. So heavy cuts can be taken.
5. Setup is easy & downtime for different work pieces will be minimal.
6. Clamp force is consistent & predictable. Work holder does not distort
the work piece.
7. Unciamping is on the tip of a button, which increases productivity.
8. No Heat is generated by integrating coil when magnet is activated, as
power supply is disconnected during machining being Electro Perm Magnetism.
9. Full Machining Capacity can be Exploited with better tolerances & repeatability.
Sr. No.
Cat No.
Size (mm)
1
UL - 82101
Ø 300 x 100 H
2
UL - 82102
Ø 450 x 100 H
3
UL - 82103
Ø 500 x 100 H
4
UL - 82104
Ø 600 x 100 H
5
UL - 82105
Ø 1000 x 100 H
6
UL - 82106
Ø 1250 x 100 H
7
UL - 82107
Ø 1500 x 100 H
" ULTRA" VARIABLE CONTROL UNIT FOR ABOVE CHUCKS
"ULTRA" EXTENSION BLOCK
"ULTRA" EXTENSION JAWS (Movebal)
   
 
 
 
MAGNETIC ROUND CHUCK FOR GRINDING
Series UL - 815
MAGNETIC ROUND CHUCK FOR GRINDING
MAGNETIC ROUND CHUCK FOR GRINDING
 
   
MAGNETIC ROUND CHUCK FOR GRINDING
 

• ELECTROPERM MAGNETIC ROUND CHUCK FOR GRINDING

Feature :
1. Continuous Electricity is not required. 100% safe in used
2. Power for all poles transferred to ring / plates to hold the job firmly
3. Assembled with power full magnets. So heavy cut can taken
4. Poles individually magnetized for full loading power

Application :

1. Use in vertical and horizontals grinding Machine.
2. Radially movable location blocks will help to position and secure work pieces.
This is also necessary for wheel clearance.

 
Sr. No.
Cat No.
Size (mm)
1
UL - 81501
Ø 300 x 100 H
2
UL - 81502
Ø 450 x 100 H
3
UL - 81503
Ø 500 x 100 H
4
UL - 81504
Ø 600 x 100 H
5
UL - 81505
Ø 800 x 100 H
6
UL - 81506
Ø 1000 x 100 H
7
UL - 81507
Ø 1250 x 115 H
" ULTRA" VARIABLE CONTROL UNIT FOR ABOVE CHUCKS
"ULTRA" EXTENSION BLOCK
"ULTRA" EXTENSION JAWS (Movebal)
Ø 1500 x 115 H
ON REQUEST
ON REQUEST
 
 
MAGNETIC PLATEN
Series UL - 210
MAGNETIC PLATEN

Introduction :
Ultra Magnetic Platen used for very fast, safe & easy clamping of moulds on Injection moulding machine. This advanced technology eliminates hydraulic & mechanical clamping system & provides quick mould change (QMC) and just in time (JIT) moulding.

Operating Principal :
Magnetic Platen works on the ELECTRO PERMANENT MAGNETIC SYSTEM that develops very high magnetic force. 
The electrical control equipment is only to activate & de-activate the magnets inside the platen i.e. it will not loose it's magnetic power in case of power failure. It doesn't requires power once it is magnetized.

Operation :
To mount a mould, the operator has to match the mould base to the locator ring on stationery platen, then bring the moving platen in until it touches the rear mould plate. Now, the operator has to magnetize the mould, remove the straps holding the mould halves together and then pull the moving platen back. The machine and mould are now ready for production.
A typical magnetic mould change involves bringing both mould halves together, securing the mould halves; demagnetizing the platen & then lifting the mould out of the press by suitable means.

Salient Features :

Universal :
• Compatibility with all existing machines
• Full utilization of active area of the platen
• Maintenance Free

Saving :
• Drastic reduction of downtime
• Virtually zero operating cost, no power consumption
• Very fast return of investment

Reliable :
• Total demagnetization of moulds & plates when switched off.
• No deformation
• Fast Clamping

Safe :
• Working on ELECTRO PERMANENT MAGNETIC SYSTEM
• Uniform clamping force across the entire rear of mould
• Uniform magnetic field.

 
Sr. No. 
Cat No.
Size (mm)
Max. working temp.
Clamping Force (Kg/Cm2)
Thickness
1.
UL21001 
Depends on Machine Platen Size
0 -130
25 - 30
60 - 65 mm
2.
UL21001 
Depends on Machine Platen Size
130-240
25 - 30
60- 65 mm
3.

ULTRA CONTROL UNIT FOR ABOVE MAGNETIC PLATEN

 
 
 
ULTRA ELECTRO MAGNETIC SQUARE BLOCK
 
ULTRA ELECTRO MAGNETIC SQUARE BLOCK

• Used as a work piece holding device for Squareness grinding inspection & light machining.
• Accuracy for Squareness & parallelism is within 0.005mm.
• Front is magnetic face. 
• Hardened strips provided on all face except back of magnetic face  for wear resistance.
• Operates on 24 VDC, controlled by Mag-D-Mag with variable control unit.
• Easy to operate.
• Saves time as mechanical clamps are avoided.
• DEMAG switch for easy removal of jobs.
• Battery back-up unit is also available on request.

 
Sr.No.
Cat No.
Size (mm)
Magnetic Pull
1.
UL-60801 
110 x 110 x 120 
125 Kg
2.
"ULTRA" MAG D - MAG WITH VARIABLE CONTROL UNIT
----------------
---------------
 
 
 
ELECTRO MAGNETIC ANGLE PLATE
 
ULTRA ELECTRO MAGNETIC ANGLE PLATE

• Used as a work piece holding device for Squareness grinding, inspection &  light machining. 
• Accuracy for Squareness & parallelism is within 0.005mm.
• Operates on 24 VDC, controlled by Mag-D-Mag with variable control unit. 
• Easy to operate. 
• Saves time as mechanical clamps are avoided. 
• DEMAG switch for easy removal of  jobs.
• Battery back-up unit is also available on request.

 
Sr.No.
Cat No.
Size (mm)
Magnetic Pull
1.
UL-60801 
150 x 150 x 160 
125 Kg
2.
"ULTRA" MAG D - MAG WITH VARIABLE CONTROL UNIT
----------------
---------------
 
 
 
PERMANENT MAGNETIC LIFTER
Series UL- 805
PERMANENT MAGNETIC LIFTER
   

• "ULTRA" brand PERMANENT MAGNETIC LIFTER
• Used for lifting & handling of steel plates, heavy block & castings as well as heavy round or cylindrical parts.
• The 1 : 3.5 safety factor of the recommended load to the Test load ensures use at optimal working conditions even with Substantial air gaps & surface conditions.
• Compact design, strong magnetic pull, total work safety
• Easy operated lever for ON-OFF.
• Spring loaded block at side fors safety feature.
• Suitable for Flat & Round jobs.
• No damage on job during operation.

   
PERMANENT MAGNETIC LIFTER
 
Sr. No. 
Cat No.
Size (mm)
Lifting Capacity for flat job
Tested Capacity for flat job
Weight
0
UL 80500
90 L X 65 W X 85H
100 Kg
350 Kg
4 Kg
1.
UL 80501 
170 L x 85 W x 105 H
200 Kg
700 Kg
9 Kg
2.
UL 80502
170 L x 85 W x 105 H
250 Kg
875 Kg
9 Kg
3.
UL 80503
230 L x 85 W x 105 H
300 Kg
1050 Kg
13 Kg
4.
UL 80504
230 L x 85 W x 105 H
450 Kg
1575 Kg
14 Kg
5.
UL 80505
255 L x 110 W x 130 H
600 Kg
2100 Kg
25 Kg
6.
UL 80506 
290 L x 110 W x 130 H
700 Kg
2450 Kg
30 Kg
7.
UL 80507
350 L x 130 W x 135 H
1000 Kg
3500 Kg
45 Kg
8.
UL 80508 
405 L x 150 W x 160 H
1500 Kg
5250 Kg
68 Kg
9.
UL 80509
470 L x 170 W x 185 H
2000 Kg
7000 kg
103 Kg
10.
UL 80510
570 L x 300 W x 270 H
3000 kg
9000 kg
280 Kg
11.
UL 80511
730 L x 350 W x 310 H
5000 kg
15000 Kg
540 Kg
 
 
 
PERMANENT MAGNETIC LIFTERS
Series UL - 810
AUTOMATIC PERMANENT MAGNETIC LIFTER
AUTOMATIC PERMANENT MAGNETIC LIFTER

Features :
• "ULTRA" brand AUTOMATIC PERMANENT MAGNETIC LIFTER
• Strong magnetic path produced by the NDFEB magnet.
• ON & OFF of the magnetic force is controlled by hanger connected to this product up & down.
• The magnetic lifter have the feathers of strong attraction,small size & weight, powerful force.
• Safety factor of automatic magnetic lifter is 1 :3 times.
• Automatic permanent magnetic lifter are available from 1000kg to 3000kg.
No electric supply is required.
• Suitable for flat jobs.


APPLICATION :

• This type of lifter widely used in moulding & machanism manufacturing such as
• Machine shop,
• Dockyard that related to steel material,
• Heavy fabrication shop,
• Various automates,
• Handling steel plates heavy blocks.

 
Cat No.
Capacity
Tested Capacity
UL- 81001
1000 Kg
3000 Kg
UL- 81002
2000 Kg
6000 Kg
UL- 81003
3000 Kg
9000 Kg
 
 
 
Ultra MAGNETIC LIFTER
"ULTRA" brand CUSTOM MADE MAGNETIC LIFTER (Electrical / Electropermanent)
Series UL- 827
 
"ULTRA" EPM Lifter for Angles
"ULTRA" EPM Lifter for Channel
"ULTRA" EPM Lifter for Round
"ULTRA" brand EPM Lifter for Angles
"ULTRA" brand EPM Lifter for Channel
"ULTRA" brand electro magnet lifter for Round
 
"ULTRA" EPM Lifter for Pipes & Round Bar
"ULTRA" EPM Lifter for Billets
 
"ULTRA" brand EPM Lifter for Pipes & Round Bar
"ULTRA" brand electro magnet lifter Lifter for Billets
 
     
 
 
 
ELECTROPERM MAGNETIC LIFTER ADJUSTABLE TYPE
Series UL- 817
ELECTROPERM MAGNETIC LIFTERS

Features :
• Electroperm Magnetic Lifter is Designed to lift single bars or pipe.
• Electroperm Magnetic Lifter is having special provision to adjust the angle
  according to diameter of bars or pipe
• Electroperm Magnetic Lifter do not required continues electricity.
• Electroperm Magnetic Lifter can be used in a multiple set if the lengh of 
job is more.

Application :
• This type of lifter widely used for lifting round bar or pipe

Design :
• Designing of electroperm Mangnetic Lifter Depands upon minimum and
  maximum size of bar or pipe. (Diameter and lengh)
• Crane Capacity
• Weight of bar or pipe

 
 
 
ELECTRO MAGNETIC SHEET LIFTER
Series UL- 819
ELECTRO MAGNETIC SHEET LIFTER

Features :
• Electro Mangnetic Lifter is design with the consideration of all industrial
   safety knob, therefore they are very compact, light straingth and very
   reliable safe in use
• Electro Magnetic Lifter are work on Electricity & require 220 V or 415 supply
• Electro Magnetic Lifter is used with combination of various magnets. At fixed
  structure with provision of chain. So this will help to handle plain as well as
  bend sheet, In short it will take care of bendness of sheet
• Inching feature or variable power knob is provided, It ensure that single plate
   wili be lifteds
• Lam block - Displays the system presents.

Application :
• It is use on flame cutting machine, plazma cutting machine and water jet
  cutting machine
• It is useful for handling small as well as large plates
• Controller is having opetional facility of battery back up which helps to keep
  magnet on for 15 minutes

Design :
• Designing of electro Mangnetic Lifter Depands upon minimum and
  maximum size of plate. (Lengh x weight x thickness)
• Crane Capacity
• Weight of plates

 
 
 
ELECTRO PERMANENT MAGNETIC LIFTER
"ULTRA" brand ELECTRO PERMANENT MAGNETS LIFTERS
Series UL- 818
 
 
Plate will not fall even when Electric Power fails
   

ELECTROPERM MAGNETIC LIFTERS for Plate Handling

• EPM lifting magnet is designed with the consideration of all industrial safety knobs. Therefore they are very compact light weight high strength and very reliable and safe in use.

• Electro Perm Magnetic lifter is combination o permanent as well as electro magnet power which is required to clamp the job or declamp the job.

• Lifted plate will not failed down even electric power failed because EPM LIFTER requires power only for holding the plates and declamping the plates. So it is 100% safe for handling the plates.

Continuous Electricity is not required so it having advantage of Saving electricity over conventional Electro Magnetic Lifter.

• Electro permanent magnetic lifter is used with combination of various magnets. At fix structure with provision of chain. So this will help to handle plain as well as bend sheets in short it will take care of bendness of plates

Safety interlock key to magnetized / demagnetized. Two buttons are to be press simultaneously with help to avoid change of accident.

“Inching” feature - when the magnets is switch ON, It might lift more than a single plate. Inching operation reduces the magnetic power slowly such that additional plates, if lifted are dropped. This is used to make sure that only one plate is handled at time.

Lamp Block - Displays the systems present state.
 
Optional Units :
Radio Remote Control - Operates from a convenient distance all the function i.e. MAG / DEMAG / Inching.

ADPREM - Accidental Demagnetization Prevention Mechanism. Disable the demagnetization cycle when carrying load.

Application :
• Ideal for handling single plates in stockyards.
• Most effective in ship building industry.
• It is use on flame cutting m/c. plazma cutting m/c and water jet cutting m/c.
• It is useful for handling small as well as large plates.
• EPM Lifter is design as per customer plate sizes.
• Controller is having special facility of selector switch help for lifting small size sheets and large plates.
• It is EPM lifting system is very suitable with EOT / GANTRY / MOBILE cranes etc.
 
See the Video
 
 
ELECTRO PERMANENT MAGNETIC LIFTER (Horizontal to Vertical and Vise a Versa)

"ULTRA" brand ELECTRO PERMANENT MAGNETIC LIFTERS
Series UL- 820

Lifting Magnet Electro Permanent Magnetic
 
 
 
Lifting Magnet Electro Permanent Magnetic

Content on this page requires a newer version of Adobe Flash Player.

Get Adobe Flash player

   
   
   

Features :

• Electro Permanent Magnets for Handling in Vertical or Horizontal Position.

• EPM lifting magnet is designed with the consideration of all industrial safety knobs. Therefore they are very compact light weight high strength and very reliable and safe in use.

• Electro Perm Magnetic lifter is combination of permanent as well as electro magnet power which is required to clamp the job or declamp the job.

• Lifted plate will not fail down even when electric power fail because EPM LIFTER requires power only a for holding the plates and declamping the plates. So it is 100% safe for handling the plates.

• Continuous electricity is not required so it is having advantage of saving electricity over conventional electro magnetic Lifter.

• Electro permanent magnetic lifter is used with combination of various magnets. At fix structure with provision of chain. So this will help to handle plain as well as bend sheets in short it will take care of bendness of plates.

• Safety interlock key to magnetized / demagnetized. Two buttons are to be press simultaneously with help to avoid chance of accident.

• "Inching" feature - when the magnets is switch ON, it might lift more than a single plate. Inching operation reduces the magnetic power slowly such that additional plates, if lifted are dropped. This is used to make sure that only one plate is handled at a time.

• Lamp Block - Displays the systems present state.

• Spreader beam fitted with suspension systems / Control Panel / Indicative Tower lamp etc.

Application :

• Ideal for handling single plate in stockyards.
• Most effective in ship building industry.
• It is use on flame cutting m/c. plasma cutting m/c and water jet cutting m/c.
• It is useful for handling small as well as large plates.
• EPM Lifter is design as per customer plate sizes.
• Controller is having special facility of selector switch help for lifting small size sheets and large plates.
• It is the EPM lifting system is very suitable with EOT / GANTRY / MOBILE crane etc.




OPTIONAL UNITS :
• Radio Remote Control - Operates from a convenient distance all the function i.e. MAG / DEMAG / Inching.
• ADPREM - Accidental Demagnetization Prevention Mechanism.
Disable the demagnetization cycle when carrying load.

DESIGN :
• Designing of EPM Plate Lifter Depends upon minimum
and maximum size of plate ( length X weight X thickness)
• Crane Capacity
• Weight of Plates.


   
 
Plate Dimensions
Plate Thickness
Rated Capacitymm
Length (mm)
Width (mm)
(kg)
Min
Max
Min
Max
1500
6300
500
2500
4 - 35
4500
3000
12500
500
2500
4 - 30
7500
3000
12500
500
3500
4 - 30
10000
3000
12500
500
3500
4 - 40
12000
3000
12500
500
3500
4 - 50
17500
 
Please Specify Min. / Max. Size of the Sheet. (Length x Width x Thickness)
 
 
 
PERMANENT ELECTRO MAGNET
Rectangular Holding Magnets With Electrical Switch Off
Series UL - 823
PERMANENT ELECTRO MAGNET

Features :
1. The Permanent magnet system of these holding magnets creates a magnetic field between the center pole and the outer border of the holding surface.
2. In addition to the permanent magnet, which creates the holding force, a coil is installed. When 24V= is applied to this switch - off coil a counter pole magnetic field is set up to neutralize the permanent magnetic field. As a result work - pieces can easily be removed. 
3. These holding magnets will preferably be used when long - term holding times are required and tools should be loosened by switching on the coil for a short period. 

Holding Surface Holding Force Weight Minimum Thickness
200 mm x 60 mm 150 kg 3.0 kg 6 mm

“ULTRA” CONTROL UNIT FOR ABOVE

Special Sizes Available on Request as per Application.

 

 
 
 
ROUND PERMANENT ELECTRIC MAGNETS
Round Permanent Electric Holding Magnets with Electrical Switch off
Series UL - 822
ROUND PERMANENT ELECTRIC MAGNETS

1. The Permanent magnet system of these holding magnets creates a magnetic field between the centre pole and the outer border of the holding surface.

2. In addition to the permanent magnet, which creates the holding force, a coil is installed. When 24V= is applied to this switch - off coil a counter pole magnetic field is set up to neutralize the permanent magnetic field. As a result work - pieces can easily be removed.

3. These holding magnets will preferably be used when long - term holding times are required and tools should be loosened by switching on the coil for a short period.

 
Sr. No. 
Cat No.
Holding Surface
Holding Force
Input power
Minimum Thickeness
1
UL- 82201
Ø 20 mm
4 kg
3.6 W
2.5 mm
2
UL- 82202
Ø 35 mm
16 kg
4.6 W
30 mm
3
UL- 82203
Ø 55 mm
42 kg
9.0 W
4.5 mm
4
UL- 82204
Ø 70 mm
72 kg
13.3 W
6.0 mm
5
UL- 82205
Ø 90 mm
120 kg
21.8 W
7.5 mm
6
UL- 82206
Ø 150 mm
350 kg
44 W
7.5 mm